In recent years, sulfur (S) deficiency in wheat has become common in many areas, particularly in no-till wheat. Classic S deficiency symptoms, confirmed by soil and plant analysis, have been observed in many no-till wheat fields during periods of rapid growth in the spring. These observed deficiencies generally occur during periods of rapid growth prior to jointing, or during stem elongation.

There are two likely reasons for this: a reduction in sulfur additions to the crop from atmospheric deposition and phosphorus fertilizer applications, and cooler soil temperatures as a result of no-till planting, which slows S mineralization in the soil. The net effect of these factors is a significant reduction in the crop available S.

The photo below is a good representation of the problem. Generally the S-deficient wheat is yellow and stunted, and the problem is found in patches in the field, especially in areas where there has been previous soil erosion or soil movement. Sulfur deficiency on growing crops is often mistaken for nitrogen (N) deficiency. However, unlike N where the older leaves show firing and yellowing, with S deficiency, the pale yellow symptoms of S deficiency often appear first on the younger or uppermost leaves. 

Sulfur deficiency in wheat. Photo by Dave Mengel.

Wheat plants with S deficiency often eventually become uniformly chlorotic. The patchy S-deficient areas of the field are often found on hilltops or sideslopes where erosion has occurred and soil organic matter is reduced, or where leaching is more pronounced. In terraced or leveled fields, wheat in areas where topsoil was removed or significant cuts were made also commonly shows symptoms.

Sulfur deficiencies in wheat have been showing up early in the spring, shortly after greenup, before organic S is mineralized from soil organic matter, and before wheat roots can grow into the subsoil to utilize sulfate accumulated there. Deficiencies of S are often difficult to identify because the paling in crop color is not always obvious. Crops lacking S also may be stunted, thin-stemmed and spindly. In the case of wheat and other cereal grains, maturity is delayed. Due to the slower growth and lack of good tillering, winter annual weed competition is also enhanced.

The majority of S in soils is present in organic forms in surface soils and as sulfate. Sulfate is relatively soluble, so it tends to leach down from the surface soil into the subsoil. In many of our Kansas soils it will accumulate in the B horizon in two forms. Some will be sorbed to clay surfaces and coatings similar to the processes whereby phosphates are sorbed, though sulfate will not be adsorbed as strongly. Sulfate will also be present in the subsoil of many Kansas soils as gypsum. 

Traditionally, S deficiency was most common on high-yielding crops grown on irrigated sandy soils low in organic matter and subject to leaching. However, due to the reduced additions from the atmosphere (there is less S in the air now) and continued crop removal, an increasing number of finer-textured soils have shown S deficiency in recent years.

A soil test for available sulfate-S in the soil profile is available. For proper interpretation of this test, soil organic matter, soil texture, the crop to be grown and the expected yield level all need to be factored in. Since sulfate-S is mobile, sampling to a 24-inch depth is important. Accurate estimates of S needs cannot be made from a surface sample alone. 

However, due to the relatively high demand for S during the rapid vegetative growth phase of wheat growth, and relatively shallow rooting by the wheat crop at this time, the S measured in the deeper, subsoil levels by the test may not be available to wheat in the early spring, especially where soils are cold.

Many fields in North Central and Northeast Kansas now have an established history of S deficiency for wheat. In this situation rather than waiting for symptoms to appear, farmers may want to consider a fall application of S as a preventive measure. 

There are many S-containing fertilizer materials. Several dry materials are available that can be blended with dry phosphorus or nitrogen fertilizers for pre-plant or winter/spring topdressing.

Elemental S (typically 90% to 95% S) is a dry material marketed by several manufacturers. Before it becomes available for plant uptake, elemental S must first be oxidized by soil microorganisms to sulfate-S and this can be a slow process when surface-applied. As a result, this material is well suited for pre-plant applications. Elemental S is not well suited for corrective applications to S-deficient wheat in the spring, however, due to the time requirement for oxidation to sulfate.

Ammonium sulfate, AMS (21-0-0-24S) is a dry material that is a good source of both N and S. It has high acid-forming potential, however, and soil pH should be monitored. Ammonium sulfate is a good source to consider for both pre-plant or topdressing to correct existing sulfur deficiencies.

Gypsum (analysis varies) is calcium sulfate, and is commonly available in a hydrated form containing 18.6% S. This material is commonly available in a granulated form that can be blended with other materials. Since it is a sulfate source, it would be immediately available, and is another good source for spring topdressing. But gypsum is not as water soluble as many fertilizer materials, such as ammonium sulfate.

New N-P-S products such as Microessentials or Anchor D are ammonium phosphate materials formulated with sulfur, and in some cases micronutrients such as zinc. In most of these products the sulfur is present as a combination of elemental-S and sulfate-S. These are also good choices for pre-plant applications.

There are also liquid sources of sulfur fertilizers available.

Ammonium thiosulfate (12-0-0-26S) is the most popular S-containing product used in the fluid fertilizer industry, as it is compatible with N solutions and other complete liquid products.

Potassium thiosulfate (KTS, 0-0-17-17S) is a clear liquid product that can be mixed with other liquid fertilizers.

Application guidelines supplied by the manufacturers of both these liquid products caution that these products should not be applied directly to seed, by in-furrow or pop-up application, due to germination and seedling injury concerns. They also caution that these products should not be applied in a foliar application or as foliar sprays to actively growing plants. Topdressing with thiosulfate and UAN can be done early, before Feekes 5, and at temperatures below 70 F. But some burn can be expected, especially with KTS. These products would be good sources for pre-plant application, however.

In-furrow application of dry products at seeding is another potential way to address S needs in fields with a history of S deficiency. Care needs to be taken when applying any sulfur product in the row at seeding due to the potential for seedling injury, however. Due to the large number of products being sold, make sure to check with your supplier that a product selected is recommended for direct in row or on the seed application.

For more information see Sulfur in Kansas, K-State publication MF-2264.

For estimations of required application rates of S see Soil Test Interpretation and Fertilizer Recommendations, K-State publication MF-2586.